Jump to content

twl845

Member
  • Posts

    31
  • Joined

  • Last visited

Everything posted by twl845

  1. I think I'll go back to my original plan and let it soak for a year and consider it again. Thanks for the info.
  2. Thanks tester. that's not a problem for me.
  3. Hi Pete Can you fill me in on how WIN 10 updates are different and why I have to be concerned? Should my ignorance stop me from going through with the upgrade?
  4. Thanks Fabian for the advice. If I go ahead with the WIN 10 upgrade process over time, I will do it on a snapshot of my Raxco Instant Recovery so if it doesn't work out I can revert to my present Primary snapshot with WIN7.
  5. OK thanks. As long as EIS continues to function during the WIN10 upgrade process.
  6. Hi All, As you may be aware, Microsoft will be making WIN10 available free starting next month gradually through Windows Update. Of the folks who have been using the Preview, or anyone else who can verify, can you tell me if EIS is compatible with WIN10 as of now? Thanks in advance.
  7. Thanks Stapp and GT500 for the advice. Actually I am using Raxco Instant recovery, and have the pre EIS system on another snapshot. If I boot to that snapshot, Sleep mode works. I will try a few experiments. Thanks
  8. Hi Stapp, Thanks for the tip. I will do that if I attempt an uninstall again. The reason to re-install as I mentioned earlier is because after doing an upgrade to IS I can't use Sleep mode on my PC. The computer stays active. Do you have an idea what caused this and perhaps have a fix?
  9. Update: I created a snapshot in my Raxco Instant Recovery and booted to that snapshot so my primary snapshot with my IS would be safe. In the snapshot of my system that I made, I attempted to uninstall IS with plans of doing a re-install. Upon clicking uninstall in the menu, a window appeared saying "Uninstalling IS". The window sat there with nothing on the progress bar for at least 15 minutes. I finally gave up and did a hard shutdown, and booting up to my original snapshot. Is there a problem uninstalling?
  10. Do you think a re-install would work? I was considering it.
  11. I successfully upgraded to IS and have just one problem. I can boot up fine, shutdown fine, but if I click Sleep on my Win7 x64 computer, the monitor goes black, but the computer doesn't go into sleep mode. I have to do a hard shutdown after waiting a minute or two. When I click Sleep and the monitor goes black I can see disk activity for just under a minute, but then it goes quiet but doesn't go into Sleep mode. Has anyone had this problem after installing IS, or does anyone know what I can do? Thanks for your response in advance.
  12. GT500: Thanks for the response. See my private message.
  13. My current EAM license is good for another 338 days. Will you please tell me what the procedure would be to upgrade to EIS without losing my unused days in EAM, and how will I pay. Do I pay the full $49 for EIS and then my time is extended? What's the "license merger deal" spoken about in post #2? Thanks in advance.
  14. Thanks for the heads up. I will also wait for the update. As long as I see a green icon, I will ignore wac's warning that EAM is off.
  15. Hi all, I can't seem to find where I can configure to scan for PUPS. I've looked everywhere on my EAM GUI. I know it's probably staring me in the face, but I can't find it. Will someone kindly point it out to me? Thanks in advance.
  16. I created a support ticket and was promptly given the answer to my question. Since so many people have read my post unable to answer my question, I include it here to help you all. If you upgrade to EIS you pay $29.96 and you will be registered for the coming year, and as in my case my present 196 days will be added to the year.
  17. Hi all, I have 196 days remaining on my EAM, which costs $29.96. I clicked the renew box and scrolled to Upgrade where it says I can upgrade to EIS for $29.96. Does it know enough to prorate the unused 196 days on my EAM and charge me less for the EIS, or do I have to pay $29.96 again. If that's the case I will wait until my present EAM year has a few days left. Thanks in advance for your response.
  18. Did the v9 update. I like the GUI, and the ease of navigation. The update went quick and smooth. No problems that I'm aware of.
  19. Thanks for your response. Right, the 3 items are not a risk so I don't want to delete them. If they were a threat I would definetly quarantine them. So then It would be OK to uncheck them and exit?
  20. As a new member, I have done a quick scan and a smart scan. Each time the scan found 3 No Risk items, so I unchecked them. After unchecking them, I don't see a way to click Finish or some other command like End to exit the scan, so I just close Emsisoft. Is just closing Emsisoft OK or is there somewhere I should be closing the scan by clicking something? Thanks in advance.
×
×
  • Create New...